View previous topic :: View next topic |
Author |
Message |
ealandbob Snailer
Joined: 28 Jan 2009 Posts: 90 Location: France 79 Deux Sevres
|
Posted: Fri Aug 26, 2011 7:01 pm Post subject: wiring for va1-vd1 |
|
|
I have the va1-vd1 ignition unit for visa motor but dont have the connector,
if I have to hard wire it does anyone know which wire goes where? I have the "cats" diagram but not sure as it shows numbering left to right as 654 21 87 is this correct
Many thanks
Boggy _________________ Plastic is Fantastic |
|
Back to top |
|
|
Jasu Dropped
Joined: 30 Sep 2007 Posts: 211 Location: Finland
|
Posted: Fri Aug 26, 2011 9:39 pm Post subject: |
|
|
Does this make any help..?
Pin number:
1. Ground
2. Vacuum unit
3. (No contact)
4. 2. proximity detector (static advance)
5. 1. proximity detector (maximum advance)
6. Supply
7. Ground
8. Coil
And the numbering in Haynes Manual is 6542178. I don't really remember why it is numbered that way..? _________________ Make it today, tomorrow it's probably illegal... |
|
Back to top |
|
|
Pietro Snailer
Joined: 17 Aug 2007 Posts: 13
|
Posted: Fri Aug 26, 2011 9:53 pm Post subject: |
|
|
Quote: | And the numbering in Haynes Manual is 6542178. I don't really remember why it is numbered that way..? |
Otherwise they could not make a clear schematic drawing ? |
|
Back to top |
|
|
Jasu Dropped
Joined: 30 Sep 2007 Posts: 211 Location: Finland
|
Posted: Fri Aug 26, 2011 10:21 pm Post subject: |
|
|
Pietro wrote: | Quote: | And the numbering in Haynes Manual is 6542178. I don't really remember why it is numbered that way..? |
Otherwise they could not make a clear schematic drawing ? |
Trying to remember, maybe I solved this by measuring these ground -pins, and after that thinking (from opened box) how it should connect..?
It was about 15 years ago when I need to solve it, and never needed again that knowledge, so thats the reason why it is so hard to remember... _________________ Make it today, tomorrow it's probably illegal... |
|
Back to top |
|
|
ealandbob Snailer
Joined: 28 Jan 2009 Posts: 90 Location: France 79 Deux Sevres
|
Posted: Sat Aug 27, 2011 8:11 am Post subject: |
|
|
Many thanks guys for your help,but it still doesnt clear up in what order the actual pins on the unit are numbered,if I knew it was 1to 8 left to right or 1to 8 right to left then I can connect up without blowing up the unit. Im really frustrated as engine is finished fitted to car but not able to run it !!!
Cheers for your help
Boggy _________________ Plastic is Fantastic |
|
Back to top |
|
|
Jasu Dropped
Joined: 30 Sep 2007 Posts: 211 Location: Finland
|
Posted: Sat Aug 27, 2011 10:15 am Post subject: |
|
|
I understand that number one is in at left and eight is at right. Also asked from my friend who has quite much Visa-experience, and he told they would be same way... _________________ Make it today, tomorrow it's probably illegal... |
|
Back to top |
|
|
backfire Dropped
Joined: 14 Nov 2007 Posts: 346 Location: NL, 's-Hertogenbosch
|
Posted: Sat Aug 27, 2011 10:34 am Post subject: |
|
|
If the numbers are correct then viewed from the top number one is on the left en number 8 is on the right. _________________ 2CV, with Visa turbo charged |
|
Back to top |
|
|
ealandbob Snailer
Joined: 28 Jan 2009 Posts: 90 Location: France 79 Deux Sevres
|
Posted: Sun Aug 28, 2011 8:19 pm Post subject: |
|
|
Many thanks guys,
Ill be out in the garage and hopefully have motor running tomorrow,
Again cheers
Boggy _________________ Plastic is Fantastic |
|
Back to top |
|
|
Rusty Dropped
Joined: 19 Jun 2007 Posts: 142 Location: Koudekerk ad rijn Netherlands
|
Posted: Mon Aug 29, 2011 7:43 am Post subject: |
|
|
if I remember correctly, the numbers are on the connector, so there you can see what is 1 and what is 8
I connected several visa computers and never had problems with it (only the first time, I put the wires in the same order as they are in the scedule )
greetzzzzzzzzzzz
Rusty _________________ Dyane1983 daily driver (will soon get bmw power)
2CV Pick-Up custom
AK400 in parts |
|
Back to top |
|
|
backfire Dropped
Joined: 14 Nov 2007 Posts: 346 Location: NL, 's-Hertogenbosch
|
Posted: Mon Aug 29, 2011 6:56 pm Post subject: |
|
|
Hi Rusty, ealandbob is also missing the connector _________________ 2CV, with Visa turbo charged |
|
Back to top |
|
|
ealandbob Snailer
Joined: 28 Jan 2009 Posts: 90 Location: France 79 Deux Sevres
|
Posted: Mon Aug 29, 2011 8:03 pm Post subject: |
|
|
Hi Rusty
As Backfire says the reason Im asking for the numbering is because I dont have the connector
Cheers
Boggy _________________ Plastic is Fantastic |
|
Back to top |
|
|
ealandbob Snailer
Joined: 28 Jan 2009 Posts: 90 Location: France 79 Deux Sevres
|
Posted: Fri Sep 02, 2011 7:10 pm Post subject: |
|
|
Hi Guys
Well after a few days delay (jobs around the house)I managed to get out to workshop today,completed wiring and motor fired up and ran first turn, so a great thankyou to all who helped solve my problem
Cheers
Boggy _________________ Plastic is Fantastic |
|
Back to top |
|
|
|